Adc Release 3.1 Manual do Utilizador Página 41
- Página / 489
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ADCP-70-220 •Issue 1 • November 2000 • Section 2 Operation and Maintenance
Page 2-11
© 2000, ADC Telecommunications, Inc.
NTP-004
Page 1 of 1
ADD A SECOND NETWORK ELEMENT TO AN IN-SERVICE STAND-ALONE
TERMINAL TO CREATE A RING NETWORK
Summary: This procedure describes the steps required to add a new Cellworx STN node to an
in-service, Service Access Multiplexer (SAM) node or stand-alone terminal to create a two node
ring. Only the second node in a network may be added using this procedure. If adding additional
nodes (third, fourth, etc.) to a ring system, perform NTP-003.
1. Verify the new node is powered on. If not, perform power on
procedures at the location. DLP-700
2. Verify the new node has the required RIC cards physically
installed and fibers are connected. Refer to the Cellworx
Installation manual listed in the preface of this document for
card installation or use the fiber procedure to install fibers. DLP-701
3. Launch the Cellworx Vision GUI from the X-Terminal. DLP-705
4. If an abnormal GUI session ending occurred from operator error,
time out, or other unforeseen events, it might be necessary to
free up the GUI and log back in. DLP-778
5. If adding a node to a SAM to form a ring, change the shelf type
(from a 6 to a 1) to a ring node via the thumbwheel switch on
the SC terminating EIM (TEIM). It can be located at the rear of
the shelf in slot 18. Refer to the Phase 3.1 Cellworx Installation
Manual listed in the preface of this document. Otherwise, go to
step 7. 1152693
6. Verify the RICs are installed in the SAM node and then perform
a hard reset on the SCs so they will read the new shelf type. This
will be traffic affecting. DLP-773
5. Add the Cellworx STN shelf to the standalone node. The shelf
IDs of the new node should have been set during installation and
recorded on the label provided on the inside of the front door
panel. DLP-738
6. Configure the node parameters. NTP-006
7. Perform acceptance tests on the new node. NTP-011
8. Add an expansion shelf to the new node if equipped. NTP-005
9. Save the NMIC database. DLP-745
Stop! You have completed this procedure.
- Cellworx 1
- Release 3.1 GUI Users Manual 1
- COPYRIGHT 4
- REVISION HISTORY 4
- TRADEMARK INFORMATION 4
- DISCLAIMER OF LIABILITY 4
- TABLE OF CONTENTS 5
- OPERATION AND MAINTENANCE 6
- SECTION 3 9
- GENERAL INFORMATION 9
- ABOUT THIS MANUAL 10
- Trademark Information 10
- Related Publications 10
- Admonishments 11
- General Safety Precautions 11
- FCC COMPLIANCE STATEMENT 12
- DOC Compliance 12
- FDA Compliance 12
- NEBS Compliance 12
- ISO9000 Compliance 13
- STANDARDS 13
- Page xii 14
- Page xiii 15
- Page xiv 16
- SECTION 1 18
- INTRODUCTION 18
- 2. USER INTERFACES 19
- A. NMIC RS232 Interface 20
- C. NMIC Serial Equipment Port 21
- COLOR INDICATION 22
- Page 1-6 23
- Page 1-7 24
- Page 1-8 25
- GUI is shown in Figure 1-11 26
- Page 1-10 27
- Page 1-11 28
- Page 1-12 29
- Page 1-13 30
- Page 1-14 31
- SECTION 2 32
- Page 2-2 33
- (continued) 34
- (continued) 35
- IXL-001 37
- INDEXED TASK LIST 37
- A. Fiber Routing 66
- B. Fiber Connection 69
- Connectors/Terminators 70
- Attenuators 71
- Adapters 71
- Page 2-54 74
- Page 2-55 75
- Page 2-57 77
- DEFINITION 79
- Page 2 of 11 88
- Page 3 of 11 89
- Page 6 of 11 92
- Waiting for NE to Boot 92
- Instructional Window 95
- Page 10 of 11 96
- Absolute 98
- Relative 98
- DLP- 707 100
- Page 1 of 7 101
- Page 2 of 7 102
- Page 2-83 103
- Page 4 of 7 104
- Page 5 of 7 105
- Page 6 of 7 106
- Page 7 of 7 107
- Create a Traffic Contract 108
- Delete a Traffic Contract 109
- Page 3 of 4 110
- Page 4 of 4 111
- Page 1 of 6 112
- Page 2 of 6 113
- Page 2-94 114
- Page 2-95 115
- Page 5 of 6 116
- SELECTION OPTIONS DESCRIPTION 117
- Page 1 of 1 118
- Page 1 of 8 119
- Page 2 of 8 120
- Page 3 of 8 121
- Page 4 of 8 122
- Page 5 of 8 123
- Page 6 of 8 124
- Page 7 of 8 125
- Page 8 of 8 126
- Page 1 of 5 127
- Page 2 of 5 128
- DOMAIN DESCRIPTION 129
- RESOURCE DESCRIPTION 130
- SEVERITY DESCRIPTION 131
- Page 1 of 3 132
- Page 2 of 3 133
- Page 3 of 3 134
- Page 1 of 2 135
- Page 2 of 2 136
- ALARM SEVERITY DEFINITION 140
- Page 1 of 4 144
- Page 2 of 4 145
- TESTING CONNECTIONS 154
- Page 3 of 5 155
- Page 4 of 5 156
- THRESHOLD CONFIGURATION 164
- Page 2-145 165
- MONITOR TYPE COMMENTS 166
- Page 2-149 169
- MONITOR TYPE MAX 15 MIN 170
- COMMENTS 170
- AAL1 LAYER 170
- ATM / TC LAYER 170
- MONTYPE MAX 15-MINUTE 173
- THRESHOLD 173
- ATM / TC 173
- ATM / TC, CONTINUED 174
- MONTYPE MAX 15 MIN 177
- AAL 1 LAYER 178
- STATISTIC DEFINITION 182
- Page 1 of 9 183
- Page 2 of 9 184
- Page 3 of 9 185
- Page 4 of 9 186
- Page 5 of 9 187
- Page 6 of 9 188
- Page 7 of 9 189
- Page 8 of 9 190
- Page 9 of 9 191
- InfoVision 199
- 0026-046 209
- Cellworx Vision: Retry? 211
- Page 3 of 7 214
- Page 5 of 5 227
- Page 2-209 229
- Page 2-223 243
- Page 2-224 244
- Page 2-228 248
- SELECTION 250
- (PRIMARY OR SECONDARY) 250
- DEFAULT OPTIONS DEFINITIONS 250
- PROTECTION 251
- Page 2-235 255
- Page 2-236 256
- Page 2-238 258
- Page 2-239 259
- Card View 260
- Refresh Close 260
- Page 2-242 262
- Page 2-243 263
- Page 2-244 264
- Page 2-247 267
- Page 2-248 268
- Page 2-249 269
- Page 2-250 270
- −Superframe 274
- Page 2-255 275
- 276
- Page 2-258 278
- Page 2-259 279
- ITEM STATUS DEFINITION ACTION 281
- STATUS DEFINITION 282
- Page 2-264 284
- Page 2-265 285
- Page 2-289 309
- Page 2-297 317
- CARD TYPE PROTECTION 324
- REQUIREMENTS 324
- SELECTION OPTIONS DEFINITIONS 324
- PARAMETER OPTIONS DEFINITION 327
- Reset Selected Cards? 330
- COMMAND DESCRIPTION 333
- CONFIGURING A SINGLE NMIC 334
- COMMAND DEFINITION 335
- Alarm Cut-Off? 339
- Page 1 of 10 347
- Page 2 of 10 348
- Page 3 of 10 349
- Page 4 of 10 350
- Page 5 of 10 351
- Page 6 of 10 352
- Page 7 of 10 353
- Page 8 of 10 354
- UPGRADE THE BOOTROM FLASH 355
- Page 10 of 10 356
- Page 3 of 6 362
- Page 4 of 6 363
- Page 6 of 6 365
- MODE PORT 370
- Page 2-354 374
- Page 2-355 375
- Page 2-356 376
- Page 2-361 381
- Page 2-362 382
- Page 2-363 383
- PARAMETER OPTION DEFINITION 385
- FRF.8 PVC ENDPOINT PARAMETERS 386
- Page 9 of 10 392
- Page 1 of 12 394
- Page 2 of 12 395
- Page 3 of 12 396
- Page 4 of 12 397
- Page 5 of 12 398
- Page 6 of 12 399
- Page 8 of 12 401
- Page 2-382 402
- Page 2-383 403
- Page 11 of 12 404
- Page 12 of 12 405
- CARD LEVEL 407
- PORT LEVEL 408
- Page 1 of 14 412
- Page 2 of 14 413
- Page 3 of 14 414
- Page 4 of 14 415
- Page 5 of 14 416
- Page 6 of 14 417
- Page 7 of 14 418
- Page 8 of 14 419
- Page 9 of 14 420
- Page 11 of 14 422
- Page 2-403 423
- Page 13 of 14 424
- Page 14 of 14 425
- Deleting Connections 427
- Deleting Endpoints 427
- Page 2-409 429
- Page 2-414 434
- Page 2-415 435
- Page 2-416 436
- 1 THRESHOLD CONFIGURATION 440
- Page 1 of 11 443
- 4 SAVE DATABASES 444
- 6 FTP SOFTWARE TO EACH NMIC 445
- Page 4 of 11 446
- Page 5 of 11 447
- Page 2-428 448
- Page 7 of 11 449
- Page 8 of 11 450
- Page 9 of 11 451
- 10 UPGRADE THE BOOTROM FLASH 452
- Page 11 of 11 453
- Page 2-438 458
- Page 2-439 459
- Page 2-440 460
- 11 FLASH FALLBACK 462
- 12 SOFTWARE FALLBACK 462
- PHILOSOPHY OF MAINTENANCE 464
- Trouble Analysis Procedures 464
- ALARM TROUBLESHOOTING 465
- Page 2-422 466
- Page 2-423 467
- Page 2-424 468
- Page 2-425 469
- Page 2-426 470
- Page 2-427 471
- Page 2-429 473
- Page 2-430 474
- Page 2-431 475
- Examine the 476
- at an error rate 476
- if there are any 477
- Page 2-434 478
- . Examine the physical 479
- if there are 479
- Page 2-437 481
- Page 21 of 23 484
- A. NMIC GENERATED ALARMS 485
- Page 2-442 486
- .1. WARRANTY/SOFTWARE 487
- .3. REPAIR CHARGES 488
- .5. RETURNED MATERIAL 488
Manuais e produtos relacionados com Hardware Adc Release 3.1
Hardware Adc 19717-A Manual do Utilizador
(32 páginas)
(32 páginas)
Hardware Adc LoopStar 780 Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Adc ACE-142S/142V Manual do Utilizador
(55 páginas)
(55 páginas)
Hardware Adc LoopStar 1600 Manual do Utilizador
(4 páginas)
(4 páginas)
Electrolux EHS 6651P manuali
Manuali dei proprietari e guide per l'utente per Stufe Electrolux EHS 6651P.
We fornisce 1 manuali pdf Electrolux EHS 6651P per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentários a estes Manuais