ADC MM701G Manual do Utilizador Página 87
- Página / 168
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 8: Configuring Modem Security
MM701G and MM702G User Manual 79
2 Select Add Interface, which is a link below the Security Interfaces table, to display the
Firewall Add Interface page.
3 In the
Name box, select the session (interface from the Session Name to Interface Mapping
table shown on page 78) as the external interface to which NAT is bound.
4 In the
Interface Type box, select external.
5 Click
Apply and you automatically return to the Security Interface Configuration page.
6 To bind this session with NAT to internal interfaces (private LAN-side IP addresses), click
the button
Enable NAT to internal interfaces located in the NAT column in the Security Interfaces
table. To disable the binding of this session with NAT to internal interfaces, click the button
Disable NAT to internal interfaces located in the NAT column in the Security Interfaces table.
In the Session Name to Interface Mapping table, the Session Name is the name you
assigned to a session during configuration. The Interface is the protocol type
selected for that session and corresponds to the Name: field at the top of the
page. NAT is attached to this session which is an external (WAN) interface.
- User Manual 1
- Copyright 2
- Trademark Information 2
- Disclaimer of Liability 2
- ABOUT THIS USER MANUAL 3
- DOCUMENT CONVENTIONS 4
- FCC CLASS B COMPLIANCE 4
- TABLE OF CONTENTS 5
- Table of Contents 6
- Table of Contents 7
- INSTALLING THE MODEM 9
- TEP 2—DETERMINE WHAT YOU NEED 10
- STEP 4—CONNECT CABLES 11
- Wall jack with 12
- DSL service 12
- PC, hub or other 12
- LED Status Indications 13
- Connect Cables 14
- ACCESSING THE WEB INTERFACE 15
- MODEM MANAGEMENT 15
- Assign IP Addresses 16
- TCP/IP Network Configuration 16
- TEP 2—SET UP THE WEB BROWSER 17
- Set Up the Web Browser 18
- Location Bar 19
- System Status page 20
- CONFIGURING THE LAN 21
- CONFIGURE THE LAN 22
- CONFIGURE DNS RELAY MODE 24
- CONFIGURE DHCP SERVER MODE 26
- Configure: 27
- Configure DHCP Server Mode 28
- Default Lease Time 29
- Max Lease Time 29
- DHCP Default Gateway 29
- DHCP DNS Server 29
- Ethernet Mode page 31
- Half Duplex or Full Duplex 31
- CONFIGURING THE WAN 33
- CONFIGURE A NEW WAN SESSION 34
- Session Name 35
- Virtual Path ID (VPI) 35
- Virtual Channel ID (VCI) 35
- Configure a New WAN Session 36
- PPPoE routed are identical 40
- QoS Peak Cell Rate 41
- QoS Sustainable Cell Rate 41
- QoS Maximum Burst Size 41
- EDIT A WAN SESSION 44
- Edit a WAN Session 46
- CONFIGURING 47
- SYSTEM PARAMETERS 47
- ASSIGNING USER ACCESS 48
- Assigning User Access 50
- ADD A DEFAULT GATEWAY 52
- ADD STATIC ROUTE ENTRIES 53
- Destination 54
- Static Routes table 55
- ADD SNMP COMMUNITIES 56
- Add SNMP Communities 58
- CHANGE SPANNING TREE SETTING 59
- Priority 60
- Hello Time 60
- Forward Delay 60
- SAVING CHANGES 61
- Saving Changes 62
- Rebooting the Modem 64
- CONFIGURING DSL PARAMETERS 65
- Quick Configuration 66
- Advance Configuration 68
- IMPLEMENTING A POINT-TO-POINT 71
- LAN EXTENSION 71
- COMPLETE A QUICK INSTALLATION 72
- Configure the Remote Modem 74
- Configure the Remote WAN 75
- Configure the Remote LAN 77
- 2 In the 79
- 3 Click 79
- 6 Click 83
- VERIFY CONNECTIVITY 84
- CONFIGURING MODEM SECURITY 85
- CONFIGURE NAT 86
- Configure NAT 88
- MANAGING THE MODEM 89
- View Modem Status 90
- View System Log 92
- VIEW WAN STATISTICS 93
- Rx Bad Pkts 94
- Tx Bad Pkts 94
- VIEW LAN STATISTICS 95
- Rx CRC Errors 96
- Tx Collisions 96
- SmartCNCTSecurity 97
- VIEW ATM STATISTICS 98
- View G.shdsl Link Statistics 100
- View G.shdsl Error Counters 102
- Update System Software 104
- 4 Click 105
- when prompted 105
- 5 Click 105
- Factory Defaults 106
- Reset to Factory Defaults 106
- ACCESSING THE 107
- COMMAND-LINE INTERFACE 107
- CONNECT TO THE CONSOLE PORT 108
- Modem Defaults 110
- Login admin 110
- Password password 110
- SET UP THE LAN 112
- MANAGE WAN SESSIONS 114
- Add a New Session 115
- Manage WAN Sessions 116
- Permanently Save Sessions 124
- Edit an Existing Session 125
- MANAGE DSL 126
- Configure G.shdsl Parameters 127
- Manage DSL 128
- Operating Mode 129
- View G.shdsl Configuration 132
- Monitor G.shdsl Statistics 133
- CRC Error 135
- LOSW Errors 135
- Errored Seconds 135
- View ATM Counters 136
- RESTORING FACTORY DEFAULTS 138
- UPDATING SYSTEM SOFTWARE 140
- VIEWING SYSTEM INFORMATION 141
- REBOOTING THE MODEM 142
- SPECIFICATIONS 143
- OVERVIEW 144
- VLAN Support 145
- DSL Standards 145
- ATM standards 145
- Internetworking Features 145
- WAN Protocols 146
- Security 146
- Management 146
- Software Upgrade 146
- Encapsulation 147
- • Bridge MIB - 2684 148
- • MIB 1213 - MIB II 148
- Connectors 149
- LAN Interface 149
- WAN Interface 150
- Connector Pinouts 151
- DSL Port (RJ-11) 151
- 10Base-T Port (RJ-45) 152
- Console Port (RJ-45) 152
- RATE VS. REACH 153
- Rate vs. Reach 154
- CONTACTING ADC 155
- GLOSSARY 157
- Appendix D: Glossary 159
- Index 163
- ´,^s¶4_¨ 168
Manuais e produtos relacionados com Redes ADC MM701G
Redes ADC ADCP-90-250 Manual do Utilizador
(94 páginas)
(94 páginas)
Redes ADC LoopStar MetroNID Manual do Utilizador
(12 páginas)
(12 páginas)
Redes ADC ACE-142S/142V Manual do Utilizador
(52 páginas)
(52 páginas)
Redes ADC Megabit Modem 700F Manual do Utilizador
(140 páginas)
(140 páginas)
Redes ADC 400F Manual
(74 páginas)
(74 páginas)
Redes ADC HDSL4 Manual do Utilizador
(79 páginas)
(79 páginas)
Redes ADC Release 3.1 Manual do Utilizador
(13 páginas)
(13 páginas)
Redes ADC HDSL4 Manual do Utilizador
(38 páginas)
(38 páginas)
Redes ADC 600F Manual do Utilizador
(2 páginas)
(2 páginas)
Electrolux EHS 6651P manuali
Manuali dei proprietari e guide per l'utente per Stufe Electrolux EHS 6651P.
We fornisce 1 manuali pdf Electrolux EHS 6651P per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentários a estes Manuais