Adc SG-1 Manual do Utilizador Página 11
- Página / 226
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SG1-UM-8500-03 xi
ABOUT THIS MANUAL
INTRODUCTION
This manual applies to ADC's Service Gateway (SG) system, hereafter referred to as "SG-1." This document
includes an overview of the platform, installation procedures, and an SG-1 commands reference.
ORGANIZATION
This manual includes the following chapters:
INTENDED AUDIENCE
This manual is intended for anyone needing to operate, administer, or maintain ADC’s line of Service Creation
Gateway products.
Chapter Description
Chapter 1: Overview Details features and pre-installation requirements for the SG-1
platform, including site requirements for power and cabling.
Chapter 2: Installation Provides detailed procedures for installing SG-1.
Chapter 3: Command-Line Interface (CLI) Describes the SG-1 Command-Line Interface (CLI), the steps to
access the CLI, and the steps to perform initial configuration
using the CLI.
Chapter 4: Accessing the Command Line
Interface
Details how to log on locally to an SCC or rear I/O port (if a rear
I/O card option is used) and set an IP address to allow for remote
management via a Telnet session.
Chapter 5: Using the Command Line Interface Describes how to access the command-line interface; it also
directs you to other manuals for administering, configuring, and
managing the SG-1.
Chapter 6: First-Level Commands Defines the commands available at the first command level of
each SCC.
Chapter 7: Second Level Commands Defines commands available at the second command level.
Appendix A: SG-1 Vendor-Specific Attributes Describes the vendor-specific attributes related to SG-1 EDS
architecture.
Appendix B: Redirection Server Explains how ADC’s product redirects all peers’ HTTP requests
to their personal sites as predefined in the Radius Server.
Appendix C: Product Support Provides information on how to contact the ADC Technical
Support group.
Glossary Defines abbreviations and acronyms for the SG-1 Service
Gateway system.
- SG-1 Service Gateway System 1
- REVISION HISTORY 2
- Table of Contents 3
- SG1-UM-8500-03 v 5
- List of Figures 7
- List of Figures June 30, 2006 8
- List of Tables 9
- List of Tables June 30, 2006 10
- ABOUT THIS MANUAL 11
- CONVENTIONS 12
- EU COMPLIANCE 12
- INSPECTING YOUR SHIPMENT 12
- OVERVIEW 13
- BEFORE YOU BEGIN 14
- SITE PREPARATIONS 14
- REQUIRED TOOLS AND EQUIPMENT 17
- POWER REQUIREMENTS 18
- BLANK FACEPLATE REQUIREMENT 18
- ENVIRONMENTAL REQUIREMENTS 18
- SYSTEM CABLING REQUIREMENTS 18
- 1-8 SG1-UM-8500-03 20
- INSTALLATION 21
- INSTALLING INTERFACE CABLES 22
- Straight-through cable 23
- Cross-over cable 23
- POWERING UP THE SG-1 24
- SERIAL CABLE 25
- 2-6 SG1-UM-8500-03 26
- COMMAND-LINE INTERFACE (CLI) 27
- COMMANDS AND NAVIGATION 28
- COMMAND-LINE EDITING 29
- 3-4 SG1-UM-8500-03 30
- CONNECTING TO THE CRAFT PORT 31
- LOGGING ON TO THE CRAFT PORT 31
- Welcome to SG-1 System 32
- Username: technician 32
- Password: ***** 32
- Login Successful 32
- Host> 32
- DISPLAYING THE IP ADDRESS 34
- CONFIGURING THE SG-1 35
- LOGGING ON 35
- LOGGING OFF 35
- WHAT TO DO NEXT 36
- FIRST-LEVEL COMMANDS 37
- USING DEBUG MODE 70
- SG1-UM-8500-03 6-37 73
- 6-38 SG1-UM-8500-03 74
- SG1-UM-8500-03 6-41 77
- 6-44 SG1-UM-8500-03 80
- SECOND LEVEL COMMANDS 81
- BANNER COMMAND 83
- LOOPBACK COMMANDS 88
- VLAN COMMANDS 89
- AUTHENTICATION COMMANDS 91
- ATM COMMANDS 94
- RADIUS COMMANDS 102
- ACCESS LIST COMMANDS 105
- SNMP COMMANDS 108
- TUNNEL COMMANDS 110
- TIMEOUTS COMMANDS 113
- NATIVE IP COMMANDS 114
- L2TP AND PPP COMMANDS 120
- DHCP COMMANDS 128
- IGMP COMMANDS 131
- ROUTING COMMAND 132
- DEBUG COMMANDS 151
- Appendix 159
- USER GROUP 164
- DHCP GROUP 174
- PROTOCOL GROUP 176
- SERVICE GROUP 176
- ROUTE GROUP 184
- VPDN GROUP 187
- QOS GROUP 191
- DNS GROUP 194
- ORUP COMMANDS 197
- SERVICE NAME COMMANDS 198
- TFTP COMMANDS 199
- SHOW COMMANDS 202
- ETHERNET COMMANDS 204
- DEFAULT GATEWAY COMMANDS 206
- USING RELOAD COMMAND 207
- WRITE COMMANDS 208
- USING POWEROFF COMMAND 209
- HTTP COMMANDS 211
- NAME SERVER 213
- USING HOSTNAME COMMAND 215
- IP-IN-IP COMMANDS 216
- SHOW USER COMMANDS 218
- USING DEBUG PROTOCOL COMMAND 219
- USING REST WEB COMMAND 219
- USING DATE COMMAND 220
- C-2 SG1-UM-8500-03 222
- GLOSSARY 223
- Glossary June 30, 2006 224
- GL-2 SG1-UM-8500-03 224
- Certification and Warranty 225
- User Manual 226
Manuais e produtos relacionados com Hardware Adc SG-1
Hardware Adc CRA-C Manual do Utilizador
(86 páginas)
(86 páginas)
Hardware Adc LSZH Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Adc Soneplex 3192 Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Adc WMX 300 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Adc FL1000 Manual do Utilizador
(4 páginas)
(4 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.247 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais